查看SKU:RB-02S113 九軸姿態檢測傳感器的源代碼

[[文件:02S11301.png|400px|縮略圖|右]]
==產品概述==
九軸姿態檢測傳感器基于MPU-9150開發而成，MPU-9150是世界上第一款集成了三軸陀螺儀、三軸加速度計及三軸磁力計的芯片。MPU-9150主要應用于低功耗、低價格和高性能消費電子產品，包含智能手機、平板電腦和可穿戴設備中。MPU-9150包含三個16位ADC用于陀螺儀信號進行數字化輸出、三個16位ADC用于加速度計信號數字化輸出及三個13位ADC用于磁力計信號數字化輸出。九軸姿態檢測傳感器可廣泛應用于航模無人機，機器人，天線云臺，聚光太陽能，地面及水下設備，虛擬現實，人體運動分析等需要低成本、高動態三維姿態測量的產品設備中。

==規格參數==
* 工作電壓：5V
* 接口類型：IIC通訊接口
* 輸出信號：數字信號
* 工作溫度：-5℃到75℃
* 接口類型：KF2510-4P防插反接口
* 通信接口：IIC 通信
* 三軸陀螺儀量程可由用戶設定，包含±250, ±500, ±1000, and ±2000°/sec
* 三軸加速度量程可由用戶設定，包含±2g, ±4g, ±8g and ±16g
* 產品尺寸：30mm x 25mm
* 固定孔尺寸：23mm x 18mm
* 重量大?。?g
* 工作電流：20mA
* 安裝：4 * M3 定位孔
* 產品尺寸：
[[文件:02S11302.png|500px|縮略圖|居中]]
* 引腳定義：
（1）-：電源地<br/>
（2）+：電源正極<br/>
（3）SDA：IIC數據信號<br/>
（4）SCL：IIC時鐘信號<br/>
==使用方法==
* 硬件環境：
（1）Starduino UNO R3 控制器<br/>
（2）4P 傳感器連接線<br/>
（3）9軸姿態傳感器<br/>

* 軟件環境：Arduino IDE 1.8.1

* 硬件連接
[[文件:02S11303.png|480px|縮略圖|居中]]
* 例子程序：
<pre style='color:blue'>#include "Wire.h"
// I2Cdev and MPU9250 must be installed as libraries, or else the .cpp/.h files
// for both classes must be in the include path of your project
#include "I2Cdev.h"
#include "MPU9250.h"

// class default I2C address is 0x68
// specific I2C addresses may be passed as a parameter here
// AD0 low = 0x68 (default for InvenSense evaluation board)
// AD0 high = 0x69
MPU9250 accelgyro;
I2Cdev   I2C_M;

uint8_t buffer_m[6];

int16_t ax, ay, az;
int16_t gx, gy, gz;
int16_t   mx, my, mz;



float heading;
float tiltheading;

float Axyz[3];
float Gxyz[3];
float Mxyz[3];


#define sample_num_mdate  5000      

volatile float mx_sample[3];
volatile float my_sample[3];
volatile float mz_sample[3];

static float mx_centre = 0;
static float my_centre = 0;
static float mz_centre = 0;

volatile int mx_max =0;
volatile int my_max =0;
volatile int mz_max =0;

volatile int mx_min =0;
volatile int my_min =0;
volatile int mz_min =0;


void setup() {
  // join I2C bus (I2Cdev library doesn't do this automatically)
  Wire.begin();

  // initialize serial communication
  // (38400 chosen because it works as well at 8MHz as it does at 16MHz, but
  // it's really up to you depending on your project)
  Serial.begin(38400);

  // initialize device
  Serial.println("Initializing I2C devices...");
  accelgyro.initialize();

  // verify connection
	Serial.println("Testing device connections...");
	Serial.println(accelgyro.testConnection() ? "MPU9250 connection successful" : "MPU9250 connection failed");
	
	delay(1000);
	Serial.println("     ");
 
	//Mxyz_init_calibrated ();
  
}

void loop() 
{   
	
	getAccel_Data();
	getGyro_Data();
	getCompassDate_calibrated(); // compass data has been calibrated here 
	getHeading();				//before we use this function we should run 'getCompassDate_calibrated()' frist, so that we can get calibrated data ,then we can get correct angle .					
	getTiltHeading();           
	
	Serial.println("calibration parameter: ");
	Serial.print(mx_centre);
	Serial.print("         ");
	Serial.print(my_centre);
	Serial.print("         ");
	Serial.println(mz_centre);
	Serial.println("     ");
	
	
	Serial.println("Acceleration(g) of X,Y,Z:");
	Serial.print(Axyz[0]); 
	Serial.print(",");
	Serial.print(Axyz[1]); 
	Serial.print(",");
	Serial.println(Axyz[2]); 
	Serial.println("Gyro(degress/s) of X,Y,Z:");
	Serial.print(Gxyz[0]); 
	Serial.print(",");
	Serial.print(Gxyz[1]); 
	Serial.print(",");
	Serial.println(Gxyz[2]); 
	Serial.println("Compass Value of X,Y,Z:");
	Serial.print(Mxyz[0]); 
	Serial.print(",");
	Serial.print(Mxyz[1]); 
	Serial.print(",");
	Serial.println(Mxyz[2]);
	Serial.println("The clockwise angle between the magnetic north and X-Axis:");
	Serial.print(heading);
	Serial.println(" ");
	Serial.println("The clockwise angle between the magnetic north and the projection of the positive X-Axis in the horizontal plane:");
	Serial.println(tiltheading);
	Serial.println("   ");
	Serial.println("   ");
    Serial.println("   ");



	delay(300);




	
}


void getHeading(void)
{
  heading=180*atan2(Mxyz[1],Mxyz[0])/PI;
  if(heading <0) heading +=360;
}

void getTiltHeading(void)
{
  float pitch = asin(-Axyz[0]);
  float roll = asin(Axyz[1]/cos(pitch));

  float xh = Mxyz[0] * cos(pitch) + Mxyz[2] * sin(pitch);
  float yh = Mxyz[0] * sin(roll) * sin(pitch) + Mxyz[1] * cos(roll) - Mxyz[2] * sin(roll) * cos(pitch);
  float zh = -Mxyz[0] * cos(roll) * sin(pitch) + Mxyz[1] * sin(roll) + Mxyz[2] * cos(roll) * cos(pitch);
  tiltheading = 180 * atan2(yh, xh)/PI;
  if(yh<0)    tiltheading +=360;
}



void Mxyz_init_calibrated ()
{
	
	Serial.println(F("Before using 9DOF,we need to calibrate the compass frist,It will takes about 2 minutes."));
	Serial.print("  ");
	Serial.println(F("During  calibratting ,you should rotate and turn the 9DOF all the time within 2 minutes."));
	Serial.print("  ");
	Serial.println(F("If you are ready ,please sent a command data 'ready' to start sample and calibrate."));
	while(!Serial.find("ready"));	
	Serial.println("  ");
	Serial.println("ready");
	Serial.println("Sample starting......");
	Serial.println("waiting ......");
	
	get_calibration_Data ();
	
	Serial.println("     ");
	Serial.println("compass calibration parameter ");
	Serial.print(mx_centre);
	Serial.print("     ");
	Serial.print(my_centre);
	Serial.print("     ");
	Serial.println(mz_centre);
	Serial.println("    ");
}


void get_calibration_Data ()
{
		for (int i=0; i<sample_num_mdate;i++)
			{
			get_one_sample_date_mxyz();
			/*
			Serial.print(mx_sample[2]);
			Serial.print(" ");
			Serial.print(my_sample[2]);                            //you can see the sample data here .
			Serial.print(" ");
			Serial.println(mz_sample[2]);
			*/


			
			if (mx_sample[2]>=mx_sample[1])mx_sample[1] = mx_sample[2];			
			if (my_sample[2]>=my_sample[1])my_sample[1] = my_sample[2]; //find max value			
			if (mz_sample[2]>=mz_sample[1])mz_sample[1] = mz_sample[2];		
			
			if (mx_sample[2]<=mx_sample[0])mx_sample[0] = mx_sample[2];
			if (my_sample[2]<=my_sample[0])my_sample[0] = my_sample[2];//find min value
			if (mz_sample[2]<=mz_sample[0])mz_sample[0] = mz_sample[2];
						
			}
			
			mx_max = mx_sample[1];
			my_max = my_sample[1];
			mz_max = mz_sample[1];			
					
			mx_min = mx_sample[0];
			my_min = my_sample[0];
			mz_min = mz_sample[0];
	

	
			mx_centre = (mx_max + mx_min)/2;
			my_centre = (my_max + my_min)/2;
			mz_centre = (mz_max + mz_min)/2;	
	
}






void get_one_sample_date_mxyz()
{		
		getCompass_Data();
		mx_sample[2] = Mxyz[0];
		my_sample[2] = Mxyz[1];
		mz_sample[2] = Mxyz[2];
}	


void getAccel_Data(void)
{
  accelgyro.getMotion9(&ax, &ay, &az, &gx, &gy, &gz, &mx, &my, &mz);
  Axyz[0] = (double) ax / 16384;//16384  LSB/g
  Axyz[1] = (double) ay / 16384;
  Axyz[2] = (double) az / 16384; 
}

void getGyro_Data(void)
{
  accelgyro.getMotion9(&ax, &ay, &az, &gx, &gy, &gz, &mx, &my, &mz);
  Gxyz[0] = (double) gx * 250 / 32768;
  Gxyz[1] = (double) gy * 250 / 32768;
  Gxyz[2] = (double) gz * 250 / 32768;
}

void getCompass_Data(void)
{
	I2C_M.writeByte(MPU9150_RA_MAG_ADDRESS, 0x0A, 0x01); //enable the magnetometer
	delay(10);
	I2C_M.readBytes(MPU9150_RA_MAG_ADDRESS, MPU9150_RA_MAG_XOUT_L, 6, buffer_m);
	
    mx = ((int16_t)(buffer_m[1]) << 8) | buffer_m[0] ;
	my = ((int16_t)(buffer_m[3]) << 8) | buffer_m[2] ;
	mz = ((int16_t)(buffer_m[5]) << 8) | buffer_m[4] ;	
	
	//Mxyz[0] = (double) mx * 1200 / 4096;
	//Mxyz[1] = (double) my * 1200 / 4096;
	//Mxyz[2] = (double) mz * 1200 / 4096;
	Mxyz[0] = (double) mx * 4800 / 8192;
	Mxyz[1] = (double) my * 4800 / 8192;
	Mxyz[2] = (double) mz * 4800 / 8192;
}

void getCompassDate_calibrated ()
{
	getCompass_Data();
	Mxyz[0] = Mxyz[0] - mx_centre;
	Mxyz[1] = Mxyz[1] - my_centre;
	Mxyz[2] = Mxyz[2] - mz_centre;	
}</pre>

* 程序效果
將程序下載后，將九軸姿態檢測傳感器水平靜止放置，打開串口監視器，波特率調整為38400，等待顯示“Initializing I2C devices... Testing device connections... MPU9250 connection successful”后晃動傳感器，觀察數據變化。

==相關推薦==

===例程下載===
* 產品例子程序及庫文件下載鏈接：http://pan.baidu.com/s/1pK9ybyF 密碼：i8hb